Guitar Electronics
If you reached this page via an Internet search engine please note:
A frame set with links to all our different sections should appear on the left of the screen.
If it's not there, log off and use: File/Open "www.GRGuitars.com"
to see our entire offering of instruments and repair parts.

Table of Contents

See Tele Parts, Strat Parts, Gibson Parts and Bass Parts pages for wiring kits.
Wire Set-Vintage style cloth covered wire set, 22 gauge-2 feet each of black and off white, lightly waxed and tinned. Same wire as used in the manufacture of Duncan Pickups
2.95
GW832B
 Wire Set-Vintage style cloth covered wire set, 22 gauge-10 feet each of black and off white, lightly waxed and tinned. 6.95

GW820

 Wire -Vintage Gibson Style wire with braided shield-4 feet-not recommended for use with Fender-style pickups
3.75

GW820B

 Wire -Vintage Gibson Style wire with braided shield-10 feet-not recommended for use with Fender-style pickups. Wire is pictured above with the Gibson wiring kit.
7.95
GW817B
 Black 22 gauge plastic coated wire-4' length for general purpose wiring. 1.95
GW817W
 White 22 gauge plastic coated wire-4' length for general purpose wiring. 1.95
GW817WB
 White 22 gauge plastic coated wire-10' length for general purpose wiring. 4.75
GW834
 Wire-black 2 conductor shielded, for pickups-4' length
3.25
GW836
 Wire-black 4 conductor foil shielded, for pickups-4' length.
Closeup at right of stripped section. Silver foil is wrapped around inside wires.
3.95

GW073

 Heat shrink tubing 1/8" x 2 feet. Heat quickly with a match or similar flame. Be careful.
2.95
GW074
Pics & Info
Heat Shrink tubing 1/16" x 2 feet
2.95
GW829c
 Chrome shielding tape 2" x 5' self stick backing 4.95

GW499

 Copper shielding Tape 1" x 5 feet, self stick backing
5.95
GW4991
 Copper shielding Tape 12" x 12" self stick backing
7.95
Pots
EP4985
 250K Linear Pot for Tone-CTS, split, knurled shaft with hardware, used for Strat
4.95
EP085
 250K Audio Pot-CTS, split, knurled shaft with nut, lock and dress washer-used for Strat
4.95
EP0885
 250K Audio taper Pot-CTS, solid shaft, with nut, lock & dress washer-use with Tele metal knobs
4.95
EP385
 Dual 250K Balance/blend audio taper pot-with hardware. Center detente, split shaft. Mini size, total length about 1 1/4" long. Two rows of 3 sets of connectors.
10.95
EP4685
 250K Audio pot-3/4" long shaft, threaded bushing, split shaft with hardware. CTS
7.95
EP285
 250K Push/pull audio taper pot with nut and washer, split shaft
10.95

EP286
 500K Push/pull audio taper pot with nut and washer, split shaft.
Same size as above. Total length about 1 3/4" long.
Size comparison: EP286 left--EP4486 on right
Far left: #EP086, Middle: #EP686-same size as EP-PAT500
Far Right, above: #EP286 Push/Pull pot
10.95
EP-500PP-US
 500k ohm pot with push/pull actuator switch used for humbucking pickups. Provides capability for such applications as coil tapping, splitting, and phasing. 3/8-32 US thread and 24 splines - length of threaded bushing 3/8 in. - length of shaft 3/8 in.

14.95
EP-PPAT-520
 Gibson brand 500k audio taper push/pull short shaft pot. 18 spline, for metric bell type knobs.
24.95
EP-PAT500
 Gibson brand Potentiometer-500K ohm Audio Taper, 3/4" long shaft, 1 piece
12.95
EP-PAT300

 Gibson brand Potentiometer- 300K ohm Linear Taper, long shaft, 1 piece
12.95
EP-PAT310

 Gibson brand Potentiometer- 300K ohm Linear Taper, short shaft, 1 piece
12.95
EP4880
 300k Audio Pot, CTS split shaft, short
5.45
EP0686
 500K CTS 3/4" long shaft audio pot, threaded section of shaft is 3/4" long. About 1 5/8" tall from bottom of base to top of split shaft. For Gibson Les Paul or guitars with thick tops. Length of threaded part of the shaft is 3/4"
7.95
EP086
 500K audio pot, short CTS split, knurled shaft with nut, lock and dress washer. Used for Gibson SG, some Gibson Historics and Strat-shorter shaft than above. These pots are sized for a 3/8" hole. Length of threaded part of shaft is 3/8"
5.45
EP4986
 500K linear pot for tone, CTS split, knurled shaft with nut, lock and dress washer.
This pot is normally used for volume/tone with stacked bass knobs. Total length of shaft from top of pot is 7/8"
5.25
EP086Lf
 Lefty 500K short audio pot, CTS split, knurled shaft with nut, lock and dress washer. Used for Gibson SG, some Gibson Historics and Strat-shorter shaft than above.
4.95
EP886
 500K short Audio taper Pot, CTS, solid shaft
4.95
EP386
 Dual 500K Blend/balance mini audio taper pot, center detente, split shaft with hardware. Two rows of 3 sets of connectors.
Total length about 1 3/8" from base to top.
10.95
EP186
 500K mini pot-Audio taper 3/8" long bushing, split knurled shaft
2.95
EP4585
 Stacked Concentric Pots 500K/250K, includes nut and washer (1)
11.95
EP4586
 Stacked Concentric Pots 500K/500K, solid shaft, includes nut and washer (1)
This pot is normally used for volume/tone with stacked bass knobs. Total length of shaft from top of pot is 7/8"
11.95
EP4645
 25K audio pot-3/4" long threaded bushing, standard size CTS, split shaft with hardware. If this pot protrudes too far up, just use a two nuts before installing the knob.
6.50
EP4745
 25K Blend/Balance audio taper pot 11.50
EP4988
 1 Meg audio taper pot-CTS split, knurled shaft. 5.95
EP88
 1 Meg linear taper pot. Standard size CTS split knurled shaft, with nut and washer 5.95
EP1906
 Fender brand 1 meg 10% audio metal pot-solid shaft
 6.50
EP282
 50K mini pot. Audio taper, split shaft. Total length of shaft about 1 1/16" 3.95
Caps
EP060C
.1 mfd poly Cap-Commonly used for bass-two pieces
Measures .45" by .67"
1.45
EP061C
 .01 mfd Ceramic Disc Capacitor-two pieces
 1.45
EP057C
 .001 mfd Cap-used for volume controls-two pieces
1.45
EP056C
 .02 mfd Ceramic Disc Capacitor-two pieces. Commonly used with Humbuckers
1.45
EP630-022C
 .022 Poly cap, 630 volts, 2 pieces 1.45
EP4382C
 .022mfd Sprague Orange Drop cap, 200 volt, 1 piece 2.50
EP059C
 .033 mfd Ceramic Disc Capacitor-two pieces
1.50
EP158C
 .47 mfd Ceramic Disc Capacitor-two pieces
This is the standard cap used for single coil pickups.
1.50
EP105C
.05 mfd Ceramic Disc Cap, 2 pieces. Length including leads, 1 1/4"
1.25
EP054C
.005 mfd cap
1.50
EP-Res15k
15K Resistor, used for Broadcaster
EP-res56k
56k Resistor for Jaguar, 1 piece. 1/2 watt carbon composition
Switches
EP075
 3-Way Switch-with screws, for Strat or Tele-switch tip not included
10.95
SW99-2041
 Fender brand 3-way switch- with screws and tip
List $14		 12.95

EP4374
 4-Way-Switch-with screws, for Tele
14.95
EP076
 5-Way Switch-with screws, for Strat, switch tip not included
10.95
SW99-1367
 Fender brand 5-way switch with tip and screws. List $14
 10.95

 

Chrome, black, white, mt green, etc. Switch knob-1 piece push on type, for Strat

See Strat Page, bottom section for more switch knobs.

  
JZJG260WH
 Slide Switch-white knob, 2 position, on-on with mounting screws. For Jaguar/Jazzmaster and similar applications.
$5.95

 
JZJG260-BK
 Jazzmaster/Jaguar Slide Switch-Black knob, 2 position on-on with mounting screws. 1 1/4" spacing between screws, total length 1 3/8", for original models.
Switchcraft brand, made in the USA.
$5.95
See Jazzmaster/Jaguar/ Mustang page for more electronics specific to these Fender instruments.
EP066
 Short Straight toggle switch chrome with black knob. About 2" from base to top of knob. See above for size comparison 12.95
EP66G
 Short Straight toggle switch gold hardware with black knob. About 2" from base to top of knob. See above for size comparison 14.50
EP067
 Medium Straight toggle switch with black knob. About 2 1/4" from base to top of knob.
See above for size comparison 		13.95
EP4367
 Straight toggle switch with cream knob, Switchcraft. Same size as Gibson TS010, below. See above for size comparison
18.95
EP4365
 Right angle toggle switch with black knob, Switchcraft
18.95
EP4369
 Straight toggle switch-for 3 pickup Les Paul, Switchcraft, with knob. This switch is the same length as the Gibson TS020 & EP4367
18.95
EP6-890C
 Set of 3-nut, washer and star washer for full size pots or input jacks. 1 piece of each
1.00
EP68C
 Extra chrome nuts for full size pots and input jacks-5 pieces
3/8"
1.00
EP69C
 Extra chrome star washers for full size pots and input jacks-5 pieces
1.25
EP70C
 Extra chrome dress washers for full size pots and input jacks-5 pieces
1.25
EP4923
 Deep thread nickel round nut for Switchcraft tall switches: EP4365, EP4367 & EP4369. These are sometimes used on Les Paul or archtop.
2.85
EP921
 Deep thread round nickel nut for Switchcraft switches EP066-short toggle switch, EP067-medium height toggle and right angle toggle switch
2.85
EP4924
 Black Rubber bushing for toggle switch. Flat bottom measures about 1 1/4" across, Center hole is 1/2" wide. List $15 For L-5 and similar guitars
To use the rubber bushing, a deep thread nut is needed on the switch , such as #EP067 switch with EP921.
12.95
Mini Switches-used for humbucker coil-tapping, series/parallel pickup switching, phase switching.
Total length about 1 3/8" - threaded part about 5/16" - 1/4" diameter mounting hole is needed and the body cavity depth should be 5/8"
EP80C
 DPDT-On-on-on mini switch with chrome mounting hardware.
Total length about 1 3/8" - threaded part about 5/16" - 1/4" diameter mounting hole is needed and the body cavity depth should be 5/8"
10.95
EP80G
 DPDT-On-on-on mini switch with gold mounting hardware and switch lever.
13.95
EP81C
 DPDT-ON-on mini switch with chrome mounting hardware
7.95
EP81G
 DPDT-ON-on mini switch with gold mounting hardware
13.95
EP82C
 DPDT-On-off-on mini switch with chrome mounting hardware
7.95
EP180C
 SPDT-On-on mini switch with chrome mounting hardware
4.50
Jacks
EP55
 1/4" Input Jack-high quality USA Switchcraft brand, includes nut and washer
2.95
EP55G
 Gold 1/4" Input Jack-high quality USA Switchcraft brand, includes nut and washer.
4.45
EP654-G
 Gold nut & dress washer for 1/4" jacks and pots, 1 of each.
1.95
EP155
 1/4" Input Jack Stereo-Switchcraft, included nut and washer
3.50
EP155L
 1/4" Input long Stereo jack-Switchcraft, 3/8" threaded bushing, nut and washer. Threaded section is longer on this jack than the standard EP155.
3.45
EP159
 1/4" End Pin jack-Switchcraft for acoustic guitars, with nut and washer
This type is for an acoustic guitar.
12.95
EP4161

Nickel End pin stereo jack with nut and washer.Can be tightened from outside the guitar.


Installation instruction: The pickup hot lead is soldered to the short (tip) terminal only. The long terminal is "ring" for stereo application only. The cable shield is soldered to the jack's cable clamp terminal

 9.45
EP151
 Panel style 1/4" threaded barrel mono Switchcraft input jack, with nut and washer. Fits flush against the guitar.
8.45
EP249
 9-volt battery terminal, rigid plastic, 1 piece
1.00

EP259

 

 9-volt battery holder-fits inside control cavity. 1 piece
Color on the left is accurate. Right side of photo is too dark.
1.00